<\/p>\n

Basic Curved Piecing Instructions<\/h3>\n

For the BOM, we will be using templates to make two different versions of the Drunkard’s Path block.<\/div>\n

<\/div>\n

\n

Version 1<\/strong> is the more traditional form of the block where the quarter circle does not extend all the way to the edge of the block. It looks like this.<\/div>\n<\/div>\n

 <\/p>\n

<\/div>\n

 <\/p>\n

Version 2<\/strong> is a quarter circle that fills the entire block. This version is made with extra\u00a0background\u00a0fabric and is then trimmed to size. When these blocks are sewn together, the quarter circle will go right to the edge of the block. It looks like this.<\/div>\n

 <\/p>\n

<\/div>\n

 <\/p>\n

The following instructions cover the basics for making Version 2 of the Drunkard’s Path block using\u00a0Template 2. The same steps are followed for Version 1\/Template 1, however there is no need to trim.<\/div>\n

 <\/p>\n

\n

Step 1 – Make Templates<\/b><\/h3>\n

Print Template 2 at 100% (be sure the 1″ scale square\u00a0on the template actually measures 1 inch when printed. Some printers don’t print a true 100%.\u00a0Carefully cut out the templates on the printed lines.<\/div>\n<\/div>\n

 <\/p>\n

<\/div>\n

 <\/p>\n

\n

Step 2 – Trace Templates onto Fabric<\/b><\/h3>\n<\/div>\n

Transfer template shapes onto fabric\u00a0by tracing around the templates\u00a0using a pencil or pen. These lines will not show so don’t worry about what pen you use as long as you can see the marks.<\/div>\n

 <\/p>\n

\n

Step 3 – Cutting Instructions\u00a0<\/b><\/h3>\n

Using scissors or a rotary cutter, cut both template pieces from your fabric.<\/p>\n

 <\/p>\n<\/div>\n

 <\/p>\n

<\/p>\n

\n

Step 4 – Marking\/Pinning\u00a0<\/b><\/h3>\n<\/div>\n

Fold both the quarter circle and leg pieces in half to make a crease in the middle. Finger press or use an iron so you can easily see the crease.<\/div>\n

 <\/p>\n

<\/div>\n

 <\/p>\n

Make two additional creases by folding each end in to match the crease in the middle.<\/div>\n

 <\/p>\n

<\/div>\n

 <\/p>\n

With the quarter circle on the bottom, position the background piece on top, right sides together, aligning the center crease marks. Pin in place.<\/div>\n

 <\/p>\n

<\/div>\n

 <\/p>\n

Match the other two crease marks and pin in place.\u00a0Match the ends and pin in place. Add additional pins if you want. I prefer to add another pin in between each crease.<\/div>\n

 <\/p>\n

<\/div>\n

 <\/p>\n

\n

Step 5 – Sewing<\/b><\/h3>\n

With the background piece on top, sew using a scant 1\/4″ seam allowance. Take it slow and ease around the curve. Lift your presser foot if necessary to smooth the fabric to avoid taking tucks. Press the seam toward the quarter circle for Template 2.<\/p>\n<\/div>\n

 <\/p>\n

Step 6 – Trimming<\/b><\/h3>\n

For Version 2, trim to 6.5″ by aligning your ruler so there is a 1\/4″ allowance beyond the edge of the curve.<\/p>\n

<\/p>\n

<\/p>\n

 <\/p>\n

Repeat the same steps for Template 1. This block is to size with no additional trimming needed.<\/div>\n

The finished trim size should be 6.5″.<\/div>\n

 <\/p>\n

<\/div>\n

 <\/p>\n","protected":false},"excerpt":{"rendered":"

By Anne Deister Basic Curved Piecing Supplies Templates.\u00a0There are 2 template pages. One for each version. Printer Cardstock (recommended) Paper scissors Fabric scissors Fabric, thread, sewing machine. Quilters ruler and rotary cutter   Basic Curved Piecing Instructions For the BOM, we will be using templates to make two different versions of the Drunkard’s Path block. […]<\/p>\n","protected":false},"author":1,"featured_media":3999,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"_et_pb_use_builder":"","_et_pb_old_content":"","_et_gb_content_width":"","footnotes":""},"categories":[53,12],"tags":[],"class_list":["post-3977","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-2020-block-of-the-month","category-tutorial"],"yoast_head":"\n